I've gotten tired of the awkward positioning of the flight controllers on my PC desk. So I've decided to put together a cockpit, nothing fancy, just something that will put everything in the proper place.
I've got the platform put together, 30in x 60in, and now I have been trying to come up with an idea for a seat. I would like it to be adjustable fore and aft. Yes like a car seat, but to go to the junkyard and get one might mean bringing home uninvited guests. Anyone have any ideas for a cheap seat? I'm trying to keep the cost of the non-controling components down as much as possible. I've thought of a low beach chair (a lawn chair lower to the ground) but my imagination can't seem to come up with a method of adjustment.
I'm building a simulator cockpit, need an idea.
- Tako_Kichi
- BDG & A2A
- Posts: 2185
- Joined: 05 Jul 2006, 13:33
- Location: SW Ontario, Canada (ex-pat Brit)
How about heavy duty drawer slides of the type meant for kitchen cabinets or industrial applications, a decent hardware store should stock them. Mount one side to your base frame and the other to the frame under your seat (you might have to build a custom frame for the seat though).
Another idea would be to mount thin strips of UHMW polyethylene to the base and the underside of the seat frame with side guides to keep the seat aligned. UHMW polyethylene (commonly referred to as just UHMW) is used in industry as the preferred material for sliding surfaces as it is very slippery, very hard wearing and will support a lot of weight. It has replaced phosphor bronze slides in many applications. You would probably have to come up with a locking arrangement for the seat too otherwise you would be slip-sliding all over the place!
Most people building pits that I have seen on the net seem to go for car seats as they are adjustable fore and aft and can tilt back to find that perfect position. If you are worried about unwelcome visitors can you place it in a garage for a day or so surrounded by mouse traps?
Another idea would be to mount thin strips of UHMW polyethylene to the base and the underside of the seat frame with side guides to keep the seat aligned. UHMW polyethylene (commonly referred to as just UHMW) is used in industry as the preferred material for sliding surfaces as it is very slippery, very hard wearing and will support a lot of weight. It has replaced phosphor bronze slides in many applications. You would probably have to come up with a locking arrangement for the seat too otherwise you would be slip-sliding all over the place!
Most people building pits that I have seen on the net seem to go for car seats as they are adjustable fore and aft and can tilt back to find that perfect position. If you are worried about unwelcome visitors can you place it in a garage for a day or so surrounded by mouse traps?
Larry
E8400 Core2Duo 3 Ghz, 4 Gb DDR2 PC6400 RAM, GTX460 (1 Gb), Realtek HD O/B audio, XP Pro (SP3)
Saitek X52 HOTAS, Saitek Yoke/Throttle, Saitek Rudder Pedals, TIR 5 Pro, LG 22" WS LCD, B-K Gamer
E8400 Core2Duo 3 Ghz, 4 Gb DDR2 PC6400 RAM, GTX460 (1 Gb), Realtek HD O/B audio, XP Pro (SP3)
Saitek X52 HOTAS, Saitek Yoke/Throttle, Saitek Rudder Pedals, TIR 5 Pro, LG 22" WS LCD, B-K Gamer
I went to Wal-Mart today and looked at the beach chairs. $20.00 is cheap enough, they even have a reclining feature. Thinking the fore/aft adjustments could be locked in with a peg/hole setup. I think a carriage of some sort would eliminate the problem of the chair folding up when moving it either fowards or backwards. The draw sliders would be a good option for that. They'd have to be industrial size.
Then again how important is moving the chair at all? It's not like anyone else's butt is going to occupy it. I could secure it to the deck with some plumping brackets, the type that attach cold water pipes to floor joyces. The CPU needs to be in close proximity to the pedals as I understand the Saitek pedals are on a short leash. Plus, since it'll be in the basement I need to incase the CPU for the time it's idle. The dust down here can be thick when the woodstove is going. So that'll cut down on the room to maneuver as well.
This is the hardest part of the project, deciding everything not controller related.
Then again how important is moving the chair at all? It's not like anyone else's butt is going to occupy it. I could secure it to the deck with some plumping brackets, the type that attach cold water pipes to floor joyces. The CPU needs to be in close proximity to the pedals as I understand the Saitek pedals are on a short leash. Plus, since it'll be in the basement I need to incase the CPU for the time it's idle. The dust down here can be thick when the woodstove is going. So that'll cut down on the room to maneuver as well.
This is the hardest part of the project, deciding everything not controller related.
I can appreciate your words, more than you could have known. I've been disabled since a couple of "incidents" 10 years ago. The people I worked for retired me and since then I struggle to find something to occupy my all too young for retirment mind. Hence this project.
The pain is with me 24 hrs a day, so sometimes it's hard to tell if I'm aggravating the problem. It has a delayed fuse, there might not be any more discomfort until an hour or two later. So you are so very right, comfort and support, as much as is possible in this state, is at the forefront of my mind. For this reason a beach chair alone won't be the last configuration incorporated in the project. I think I'll be adding a wee bit of padding, much like sitting on a parachute.
As one on this side of a "bad back", I agree with your assesment , if you aint here you don't want to be, lift with your legs.
Now I have to work up the discipline to sell my motorcycle. I've probably been pushing the limits with that. Life slowly closes in.
The pain is with me 24 hrs a day, so sometimes it's hard to tell if I'm aggravating the problem. It has a delayed fuse, there might not be any more discomfort until an hour or two later. So you are so very right, comfort and support, as much as is possible in this state, is at the forefront of my mind. For this reason a beach chair alone won't be the last configuration incorporated in the project. I think I'll be adding a wee bit of padding, much like sitting on a parachute.
As one on this side of a "bad back", I agree with your assesment , if you aint here you don't want to be, lift with your legs.
Now I have to work up the discipline to sell my motorcycle. I've probably been pushing the limits with that. Life slowly closes in.
On "http://ch-hangar.com" in the Forum section there is a cockpit forum.
It shows many pix of home build cockpits from simple to very good as well as almost real cockpit home build ones.
Mine is the Old Luftwaffe Pilots cockpit, a very simple but good working one.
It is dedicated to gaming & inexpensive with a comfortable big reclining not too expensive leather chair from the "Fry's" store of which I have also one for the other working computer desk.
It shows many pix of home build cockpits from simple to very good as well as almost real cockpit home build ones.
Mine is the Old Luftwaffe Pilots cockpit, a very simple but good working one.
It is dedicated to gaming & inexpensive with a comfortable big reclining not too expensive leather chair from the "Fry's" store of which I have also one for the other working computer desk.
Joachim.
Hals und Bein Bruch,
Glider Pilot 1940 - 1942
Obergefreiter und Flugzeugfuehrer 1944[img]
Tareget, here's a solution I used as I didn't have the room for a fabricated cockpit.
Made from Gov't surplus shelving supports used in a wharehouse.
Attchment photo of the bases used for stick and throttle to the up right pieces.
Made from Gov't surplus shelving supports used in a wharehouse.
Attchment photo of the bases used for stick and throttle to the up right pieces.
"War does not determine who is right- only who is left" Bertrand Russell
Member Of Mid Atlantic Air Museum Reading, Pa.
Tour Coordinator KILG and Member of Collings Foundation Stowe, Mass
Goundcrew Member - Warbirds of Delaware KILG
Bombs-Away.net
Member Of Mid Atlantic Air Museum Reading, Pa.
Tour Coordinator KILG and Member of Collings Foundation Stowe, Mass
Goundcrew Member - Warbirds of Delaware KILG
Bombs-Away.net
LOL... thanks Snuffy. Thats not all I kept around from my trucking days. LOL
I was at Home Depot here in Bear today and ran across the same stuff my stand is made out of mixed in with the metal conduit. Check HD and that section where you are Target, they may have it too.
I was at Home Depot here in Bear today and ran across the same stuff my stand is made out of mixed in with the metal conduit. Check HD and that section where you are Target, they may have it too.
"War does not determine who is right- only who is left" Bertrand Russell
Member Of Mid Atlantic Air Museum Reading, Pa.
Tour Coordinator KILG and Member of Collings Foundation Stowe, Mass
Goundcrew Member - Warbirds of Delaware KILG
Bombs-Away.net
Member Of Mid Atlantic Air Museum Reading, Pa.
Tour Coordinator KILG and Member of Collings Foundation Stowe, Mass
Goundcrew Member - Warbirds of Delaware KILG
Bombs-Away.net
-
- Airman Basic
- Posts: 8
- Joined: 24 Mar 2007, 14:52
- Location: Camelot
Here's mine. Enjoy.
http://img526.imageshack.us/my.php?imag ... sm14xj.jpg
http://img526.imageshack.us/my.php?imag ... sm12mk.jpg
http://img526.imageshack.us/my.php?imag ... sm15kg.jpg
http://img526.imageshack.us/my.php?imag ... sm16zv.jpg
http://img380.imageshack.us/my.php?imag ... sm39aq.jpg
It's a modified Akers-Barnes cockpit. The car seat is a 2000 Dodge Intrepid (in very good condition). I examined many seats and yes, you want a seat that your body can remain in for long preiods. The sound system is a Klipsch THX. When the co-pilot and kids are out of the house, then I crank it up. Absolutley "touching" I say.
gx007
http://img526.imageshack.us/my.php?imag ... sm14xj.jpg
http://img526.imageshack.us/my.php?imag ... sm12mk.jpg
http://img526.imageshack.us/my.php?imag ... sm15kg.jpg
http://img526.imageshack.us/my.php?imag ... sm16zv.jpg
http://img380.imageshack.us/my.php?imag ... sm39aq.jpg
It's a modified Akers-Barnes cockpit. The car seat is a 2000 Dodge Intrepid (in very good condition). I examined many seats and yes, you want a seat that your body can remain in for long preiods. The sound system is a Klipsch THX. When the co-pilot and kids are out of the house, then I crank it up. Absolutley "touching" I say.
gx007
-
- BDG
- Posts: 1300
- Joined: 07 Nov 2004, 18:29
Who is online
Users browsing this forum: Google [Bot] and 65 guests