Page 1 of 1
Can't get P-51 Civ to Work With Latest Update
Posted: 22 Jun 2017, 13:20
by twsharp12
Latest Accu-Sim update breaks my P-51. It causes it to go hard left and not have any rudder control on the ground whatsoever. If I uninstall completely, including the .dat file, then reinstall the plane with accu-sim, I'll have normal functionality.
Upon running the updater it breaks again.
This is for FSX:SE.
However I have noticed that if I use Yaw control and put the plane around FL300 and let it run for a little while, it will start off going hard left then eventually fly straight after around 20 seconds. Until that 20(ish) seconds is up I have no control.
I've checked to make sure controls are unlocked and that is not the issue.
Re: Can't get P-51 Civ to Work With Latest Update
Posted: 23 Jun 2017, 10:07
by Lewis - A2A
Hello,
Just to check you have the Accu-sim package for the P-51 and not just the P-51 aircraft?
Also when updating and troubleshooting, did you try deleting the .dat file?
thanks,
Lewis
Re: Can't get P-51 Civ to Work With Latest Update
Posted: 26 Jun 2017, 08:32
by twsharp12
Lewis I took the plunge and purchased P3D V4 and also a few of my A2A planes I purchased for the P3D V4 platform. I also uninstalled FSX completely and did a full migration over.
I couldn't figure out the issue with it turning hard left on FSX. I will say I did try to install the P51 FSX version in P3D but couldn't get the accu-sim part of it to work so I gave up on that too. Although without Accu-sim on P3D it will fly without going hard left.
Any idea if the P51 will get a P3D release?
As a side-note, the Texan and Comanche flew like a dream and looks absolutely stunning on P3D V4. I look forward to when the Connie gets the V4 release.
Thanks,
Re: Can't get P-51 Civ to Work With Latest Update
Posted: 26 Jun 2017, 13:38
by Lewis - A2A
Yes we are looking at releasing P3Dv4 warbirds down the line.
thanks,
Lewis
Re: Can't get P-51 Civ to Work With Latest Update
Posted: 29 Nov 2017, 04:58
by ben78530
Hi Lewis,
regarding the Accu-sim package, where can I get it? I bought your P51 Military from FSPilotShop in 2015 and it seems that I do not have the Accu-sim package with it.
I cannot download the latest version from FSPilotShop anymore.
I did try to run the update tool A2A_Update_10_12_17 but I still have the common problem of no control on the backwheel.
The update works fine on the two other aircrafts I have from A2A (C182 and Comanche).
Not sure what to do next. Would the Accu-sim package fix the spining problem? and if so where could I get it?
I'm on P3D V4.1
Ben
Re: Can't get P-51 Civ to Work With Latest Update
Posted: 29 Nov 2017, 07:07
by Lewis - A2A
Hey Ben,
you can purchase the P-51 Accu-sim package from the A2A Store or the third party reseller you mentioned and most of the other stores too.
https://a2asimulations.com/store/index. ... 5fbac18fb7
It is not a requirement for correct use of the basic sim though, if you are having issues please do start a new thread with the exact issue you are having.
thanks,
Lewis - A2A
Re: Can't get P-51 Civ to Work With Latest Update
Posted: 29 Nov 2017, 22:03
by Skycat
ben78530 wrote:
Would the Accu-sim package fix the spining problem? and if so where could I get it?
I'm on P3D V4.1
The P-51 isn't P3D compatible yet. I'd wait until a P3D version comes out. (ETA is 2018.)
Re: Can't get P-51 Civ to Work With Latest Update
Posted: 01 Dec 2017, 08:52
by Lewis - A2A
Ahh yes, I missed that part. Yes, the P-51 you currently own is an FSX product, it was not designed for use with or under the Lockheed guidelines for the P3D platform. We hope to have the P-51 as P3D product in the first half of 2018.
thanks,
Lewis
Re: Can't get P-51 Civ to Work With Latest Update
Posted: 01 Dec 2017, 09:01
by ben78530
Guys,
ok, thanks for the tips. I'll be patient then.
Cheers,
Ben
Re: Can't get P-51 Civ to Work With Latest Update
Posted: 03 Dec 2017, 07:50
by pecquais
Mid 2018!
Dediou, c'est loin!!!