I would like to wire two switches up for the Davtron via FSUIPC. Is there a LVAR for the two switches?
Vangyver
Davtron
Re: Davtron
I thought Nick and/or Lewis mentioned a list of Lvars somewhere…I found this in the forum but I have no clue if it helps you! https://a2asimulations.com/forum/viewt ... 25&t=47493
Re: Davtron
The link you posted is for the A2A Comanche 250. Nothing there for the Davtron but has the following which I do not believe will work.
(L:ToFromNeedle,enum) - to/from flag (0 – off, 1 – to, 2 – from)
(L:ToFrom2Needle,enum) - to/from flag (0 – off, 1 – to, 2 – from)
I also have the LVAR PDF for the Piper Cherokee 180 which also has nothing for the Davtron but does list the same as above.
Thank you for your reply.
Vangyver
(L:ToFromNeedle,enum) - to/from flag (0 – off, 1 – to, 2 – from)
(L:ToFrom2Needle,enum) - to/from flag (0 – off, 1 – to, 2 – from)
I also have the LVAR PDF for the Piper Cherokee 180 which also has nothing for the Davtron but does list the same as above.
Thank you for your reply.
Vangyver
Re: Davtron
Sorry, Vangyver…my eyes…
- Nick - A2A
- A2A Captain
- Posts: 13771
- Joined: 06 Jun 2014, 13:06
- Location: UK
Re: Davtron
Hi Vangyver,
You should be able to use the three L:Vars below to operate the buttons on the Davtron clock.
L:ClockLc2LeftSwitch
L:ClockLc2MiddleSwitch
L:ClockLc2RightSwitch
I suspect for regular spring loaded buttons, you'll want to SET them to 1 when the button in question is depressed, and SET them to 0 when it's released. If you're using a two way switch, a different approach may be preferable.
Thanks,
Nick
You should be able to use the three L:Vars below to operate the buttons on the Davtron clock.
L:ClockLc2LeftSwitch
L:ClockLc2MiddleSwitch
L:ClockLc2RightSwitch
I suspect for regular spring loaded buttons, you'll want to SET them to 1 when the button in question is depressed, and SET them to 0 when it's released. If you're using a two way switch, a different approach may be preferable.
Thanks,
Nick
A2A Simulations Inc.
Re: Davtron
Sorry Nick, my bad. I should of stated it is for the Piper Cherokee 180. (DVOR) Lookong for LVARs for the Nav 1-2 switch and the To-From Switch.
Vangyver
Vangyver
Re: Davtron
I think I found it:
L:DvorNavSwitch=0
L:DvorToFromSwitch=0
It must be a value of o or 1. I will have to test it.
Vangyver
Update: Yes it works.
L:DvorNavSwitch (value of 0=Nav1 Value of 1=Nav2)
L:DvorToFromSwitch (value of 0=To Value of 1=Fr)
L:DvorNavSwitch=0
L:DvorToFromSwitch=0
It must be a value of o or 1. I will have to test it.
Vangyver
Update: Yes it works.
L:DvorNavSwitch (value of 0=Nav1 Value of 1=Nav2)
L:DvorToFromSwitch (value of 0=To Value of 1=Fr)
Who is online
Users browsing this forum: No registered users and 13 guests