Can't get P-51 Civ to Work With Latest Update

Post any technical issues here. This forum gets priority from our staff.
new reply
twsharp12
Staff Sergeant
Posts: 480
Joined: 15 Dec 2015, 09:30

Can't get P-51 Civ to Work With Latest Update

Post by twsharp12 »

Latest Accu-Sim update breaks my P-51. It causes it to go hard left and not have any rudder control on the ground whatsoever. If I uninstall completely, including the .dat file, then reinstall the plane with accu-sim, I'll have normal functionality.

Upon running the updater it breaks again.

This is for FSX:SE.

However I have noticed that if I use Yaw control and put the plane around FL300 and let it run for a little while, it will start off going hard left then eventually fly straight after around 20 seconds. Until that 20(ish) seconds is up I have no control.

I've checked to make sure controls are unlocked and that is not the issue.

User avatar
Lewis - A2A
A2A Lieutenant Colonel
Posts: 33284
Joined: 06 Nov 2004, 23:22
Location: Norfolk UK
Contact:

Re: Can't get P-51 Civ to Work With Latest Update

Post by Lewis - A2A »

Hello,

Just to check you have the Accu-sim package for the P-51 and not just the P-51 aircraft?

Also when updating and troubleshooting, did you try deleting the .dat file?

thanks,
Lewis
A2A Facebook for news live to your social media newsfeed
A2A Youtube because a video can say a thousand screenshots,..
A2A Simulations Twitter for news live to your social media newsfeed
A2A Simulations Community Discord for voice/text chat

twsharp12
Staff Sergeant
Posts: 480
Joined: 15 Dec 2015, 09:30

Re: Can't get P-51 Civ to Work With Latest Update

Post by twsharp12 »

Lewis I took the plunge and purchased P3D V4 and also a few of my A2A planes I purchased for the P3D V4 platform. I also uninstalled FSX completely and did a full migration over.

I couldn't figure out the issue with it turning hard left on FSX. I will say I did try to install the P51 FSX version in P3D but couldn't get the accu-sim part of it to work so I gave up on that too. Although without Accu-sim on P3D it will fly without going hard left.

Any idea if the P51 will get a P3D release?

As a side-note, the Texan and Comanche flew like a dream and looks absolutely stunning on P3D V4. I look forward to when the Connie gets the V4 release.

Thanks,

User avatar
Lewis - A2A
A2A Lieutenant Colonel
Posts: 33284
Joined: 06 Nov 2004, 23:22
Location: Norfolk UK
Contact:

Re: Can't get P-51 Civ to Work With Latest Update

Post by Lewis - A2A »

Yes we are looking at releasing P3Dv4 warbirds down the line.

thanks,
Lewis
A2A Facebook for news live to your social media newsfeed
A2A Youtube because a video can say a thousand screenshots,..
A2A Simulations Twitter for news live to your social media newsfeed
A2A Simulations Community Discord for voice/text chat

ben78530
Airman Basic
Posts: 5
Joined: 27 Feb 2015, 13:16

Re: Can't get P-51 Civ to Work With Latest Update

Post by ben78530 »

Hi Lewis,

regarding the Accu-sim package, where can I get it? I bought your P51 Military from FSPilotShop in 2015 and it seems that I do not have the Accu-sim package with it.

I cannot download the latest version from FSPilotShop anymore.

I did try to run the update tool A2A_Update_10_12_17 but I still have the common problem of no control on the backwheel.

The update works fine on the two other aircrafts I have from A2A (C182 and Comanche).

Not sure what to do next. Would the Accu-sim package fix the spining problem? and if so where could I get it?

I'm on P3D V4.1

Ben

User avatar
Lewis - A2A
A2A Lieutenant Colonel
Posts: 33284
Joined: 06 Nov 2004, 23:22
Location: Norfolk UK
Contact:

Re: Can't get P-51 Civ to Work With Latest Update

Post by Lewis - A2A »

Hey Ben,

you can purchase the P-51 Accu-sim package from the A2A Store or the third party reseller you mentioned and most of the other stores too.

https://a2asimulations.com/store/index. ... 5fbac18fb7

It is not a requirement for correct use of the basic sim though, if you are having issues please do start a new thread with the exact issue you are having.

thanks,
Lewis - A2A
A2A Facebook for news live to your social media newsfeed
A2A Youtube because a video can say a thousand screenshots,..
A2A Simulations Twitter for news live to your social media newsfeed
A2A Simulations Community Discord for voice/text chat

User avatar
Skycat
Senior Master Sergeant
Posts: 2191
Joined: 11 Nov 2006, 16:15
Location: Great Falls Army Air Base, Montana

Re: Can't get P-51 Civ to Work With Latest Update

Post by Skycat »

ben78530 wrote: Would the Accu-sim package fix the spining problem? and if so where could I get it?
I'm on P3D V4.1
The P-51 isn't P3D compatible yet. I'd wait until a P3D version comes out. (ETA is 2018.)
Pax Orbis Per Arma Aeria

User avatar
Lewis - A2A
A2A Lieutenant Colonel
Posts: 33284
Joined: 06 Nov 2004, 23:22
Location: Norfolk UK
Contact:

Re: Can't get P-51 Civ to Work With Latest Update

Post by Lewis - A2A »

Ahh yes, I missed that part. Yes, the P-51 you currently own is an FSX product, it was not designed for use with or under the Lockheed guidelines for the P3D platform. We hope to have the P-51 as P3D product in the first half of 2018.

thanks,
Lewis
A2A Facebook for news live to your social media newsfeed
A2A Youtube because a video can say a thousand screenshots,..
A2A Simulations Twitter for news live to your social media newsfeed
A2A Simulations Community Discord for voice/text chat

ben78530
Airman Basic
Posts: 5
Joined: 27 Feb 2015, 13:16

Re: Can't get P-51 Civ to Work With Latest Update

Post by ben78530 »

Guys,

ok, thanks for the tips. I'll be patient then.

Cheers,

Ben

pecquais
Airman
Posts: 18
Joined: 22 Mar 2014, 08:57

Re: Can't get P-51 Civ to Work With Latest Update

Post by pecquais »

Mid 2018!
:mrgreen: Dediou, c'est loin!!!

new reply

Return to “P-51 Tech Support”

Who is online

Users browsing this forum: No registered users and 10 guests