Hello mate...
I´m trying to modify the lights for the Baron 58
This is what it looks like:
gauge00=G1000!MFD_Baron, 0,0,765,500
gauge01=G1000!audio_panel, 779,513,97,511
gauge02=G1000!G1000_PFD, 0,514,765,500
gauge03=shockwave_lights!SW Lights_gear, 1,1,1,1 //shockwave light
[LIGHTS]
//Types: 1=beacon, 2=strobe, 3=navigation, 4=cockpit, 5=landing
light.0 = 3, -6.81, -19.30, 1.17, fx_shockwave_navred ,
light.1 = 3, -6.82, 19.29, 1.17, fx_shockwave_navgre ,
light.2 = 3, -25.33, 0.01, 1.08, fx_shockwave_navwhi_nl ,
light.3 = 2, -6.48, -19.04, 1.17, fx_shockwave_strobe ,
light.4 = 2, -6.48, 19.04, 1.17, fx_shockwave_strobe_2 ,
light.5 = 1, -24.20, 0.00, 6.54, fx_shockwave_beaconh_lowl ,
light.6 = 2, -7.52, 0.01, -1.28, fx_shockwave_strobe_3_nl ,
light.7 = 4, -8.30, 0.00, 3.00, fx_shockwave_vclight,
light.8 = 5, .84, 0.0, -1.5, fx_Shockwave_landing_light_small // Shockwave light
light.9 = 5, -1.4, 7.0, .1, fx_Shockwave_landing_light_small // Shockwave light
light.10 = 5, -1.4, -6.8, .1, fx_Shockwave_landing_light_small // Shockwave light
What needs to be changed?
I´ve already made changes as suggested but I end up raising the gear with a taxi light hanging below the nose as the landing lights go out automatically.
What to do, what to do!
Hey Scott!
- Scott - A2A
- A2A General
- Posts: 16839
- Joined: 11 Feb 2004, 12:55
- Location: USA
- Contact:
Re: Hey Scott!
These three lights are attached to the landing lights with their type entry of '5':
light.8 = 5, .84, 0.0, -1.5, fx_Shockwave_landing_light_small // Shockwave light
light.9 = 5, -1.4, 7.0, .1, fx_Shockwave_landing_light_small // Shockwave light
light.10 = 5, -1.4, -6.8, .1, fx_Shockwave_landing_light_small // Shockwave light
Light.8 appears to be your taxi light, and this should go off when raised. I would remove all three lines and try it, just to verify all three of these lights are being seen. Then add them back one at a time, but I do not see how these all cannot work in synch since they are the same type.
Scott.
light.8 = 5, .84, 0.0, -1.5, fx_Shockwave_landing_light_small // Shockwave light
light.9 = 5, -1.4, 7.0, .1, fx_Shockwave_landing_light_small // Shockwave light
light.10 = 5, -1.4, -6.8, .1, fx_Shockwave_landing_light_small // Shockwave light
Light.8 appears to be your taxi light, and this should go off when raised. I would remove all three lines and try it, just to verify all three of these lights are being seen. Then add them back one at a time, but I do not see how these all cannot work in synch since they are the same type.
Scott.
A2A Simulations Inc.
Who is online
Users browsing this forum: No registered users and 14 guests