PMDG 737-800 & PSS 757-200

[wildwally]

Here are the config lines for these two aircraft. Now due to the landing gear raising and light staying, I incorporated the line of code for the gauge that was provided by shockwave into the panel file for each aircraft. In addition, I added another set of light to the wing stations. So when taxi activate all the light except landing lights. The wing toggle/button turns on a dimmer version of the wing station landing lights. Then when the actual landing lights are turned on it turns up the intensity (as is the case in RL on some aircraft). After takeoff raise gear and the Landing lights turn off. After 10,000 ft turn off the wing lights and away you go. Back up old congig and give it a try.

PMDG 737-800


[LIGHTS]
//737-800
light.0 = 2, -130.000, 0.090, 5.989, fx_strobe_pmdg, //Aft Strobe
light.2 = 1, -51.750, 0.000, 8.700, fx_beaconh_pmdg, //Top Beacon Blink
light.3 = 1, -65.900, 0.000, -5.600, fx_beaconh_pmdg, //Bottom Beacon Blink
light.4 = 3, -79.000, -55.665, 2.100, fx_navred_pmdg, //Left Nav Light red
light.5 = 2, -80.000, -55.986, 2.100, fx_strobe_pmdg, //Left Strobe
light.6 = 3, -79.000, 55.665, 2.100, fx_navgre_pmdg, //Right Nav Light green
light.7 = 2, -80.000, 56.200, 2.100, fx_strobe_pmdg, //Right Strobe
light.8 = 3, -84.800, -56.737, 1.800, fx_navwhi_pmdg, //Left Position Light
light.9 = 3, -84.800, 56.691, 1.800, fx_navwhi_pmdg, //Right Position Light
light.10 = 3,-130.000, -0.090, 5.989, fx_navwhi_pmdg, //Aft Position Light
light.11 = 5, -51.60, -6.50, -1.70, fx_shockwave_landing_light_narrow.fx // Shockwave light
light.12 = 5, -51.60, 6.50, -1.70, fx_shockwave_landing_light_narrow.fx //
Shockwave light
light.13 = 6, -14.00, 0.00, -4.50, fx_Shockwave_landing_light_small.FX // Shockwave

light
light.14 = 5, -52.30, -2.50, -5.30, fx_shockwave_landing_light_narrow_down //
Shockwave light
light.15 = 5, -52.30, 2.50, -5.30, fx_shockwave_landing_light_narrow_down //
Shockwave light
light.16 = 5, -12.80, 0.00, -7.6, fx_shockwave_landing_light_narrow // shockwave
light
light.17 = 8, -51.60, -6.50, -1.70, fx_shockwave_landing_light_narrow_down.fx //
Shockwave light
light.18 = 8, -51.60, 6.50, -1.70, fx_shockwave_landing_light_narrow_down.fx //
Shockwave light



PSS 757-200

[lights]

light.1 = 7, 72.50, 1.5, 4.0, FX_PSS_Panel_light
light.2 = 7, 72.50, -1.5, 4.0, FX_PSS_Panel_light

light.3 = 9, -60.17, 3, 15.0, FX_PSS_logo_light
light.4 = 9, -60.17, -3, 15.0, FX_PSS_logo_light
light.5 = 1, 42.75, 0, 10.1, fx_shockwave_beaconh_l
light.6 = 1, 5.26, 0, -4.5, fx_shockwave_beacon_757_rotating_red.fx
light.7 = 5, 20, 7.55, -0.1, fx_shockwave_landing_light_757_lw
light.8 = 5, 20, -7.55, -0.1, fx_shockwave_landing_light_757_rw
light.9 = 6, 61.5, 0, -5.1, fx_shockwave_landing_light_double
light.10 = 8, 20, 7.6, -0.1, fx_shockwave_landing_light_narrow.fx
light.11 = 8, 20, -7.6, -0.1, fx_shockwave_landing_light_narrow.fx

[webestereo]

This configuration is not correct...

The lights are displayed way behind the aircraft.....

Anyone with a correct config?