Page 1 of 1

CH Products on P3Dv4

Posted: 16 Sep 2018, 10:50
by guillaume78150
I installed P3Dv4 but id does not recognize my Fighter Stick neither my Pro Pedals. I looked for various forum but could not find any info.
In P3D, it appears as "CONTROL001& and "CONTROL002" and can't be calibrated.
Any idea ?

Re: CH Products on P3Dv4

Posted: 16 Sep 2018, 11:25
by patful
My CH Pro pedals work in P3D4. Have you checked Devices/Printers in the Windows Control Panel to make sure Windows recognizes them and that they're functioning properly?

Re: CH Products on P3Dv4

Posted: 16 Sep 2018, 11:32
by guillaume78150
Yes, they work perfectly well with FSX on the same computer.
Strange, I read about some issues with P3Dv3, but nothing on v4...

Re: CH Products on P3Dv4

Posted: 16 Sep 2018, 11:38
by patful
Strange! Are you running P3D as Administrator?

Re: CH Products on P3Dv4

Posted: 16 Sep 2018, 11:49
by guillaume78150
Yes.

Re: CH Products on P3Dv4

Posted: 16 Sep 2018, 15:23
by dvm
When I used CH hardware I always had CH control manger installed and even if you don't use the programing features it added stability to all my CH devices. Might be worth a try. You can always uninstall it.

http://www.chproducts.com/Flight-Sim-Yo ... d-705.html

Re: CH Products on P3Dv4

Posted: 16 Sep 2018, 18:00
by guillaume78150
Thanks, I uninstalled the control manager but it did not change anything.
I will reinstall and see. Bad day, for any reason, it crashed my FSX installation and I'm now facing full reinstallation… With Orbx stuff, it will take hours...

Re: CH Products on P3Dv4

Posted: 16 Sep 2018, 19:43
by Molly - A2A
At some point during one of the P3D version updates, possible with v3, it stopped detecting my CH products correctly and auto-assigning a default button/axis layout like FSX does. Mine are labeled "controller 001, 002" etc as well. Are you able to even assign things (buttons and axes) properly? I have to go through and delete the erroneous default assignments, then add my own. It's a tedious process but once you get it down, you should be good to go.

CH Products on P3Dv4

Posted: 17 Sep 2018, 00:38
by Jacques
I just two days ago migrated to P3D v4 and used the following linked post to successfully set up my CH hardware. The yoke and pedals perform beautifully now. https://www.prepar3d.com/forum/viewtopic.php?t=128881

And...congratulations Molly on your promotion! :D

Sent from my iPad using Tapatalk

Re: CH Products on P3Dv4

Posted: 17 Sep 2018, 03:05
by guillaume78150
Thanks everybody. Will do and let you know !

Re: CH Products on P3Dv4

Posted: 22 Sep 2018, 12:43
by Lewis - A2A
P3dv4 has two input options under settings. Change this and things will probably work for you. A system or sim restart might be needed upon changing the setting.

Thanks,
Lewis

Re: CH Products on P3Dv4

Posted: 22 Sep 2018, 13:03
by alan CXA651
Hi.
I dont have P3Dv4 i use FSXA and was told dont use the CH driver disc that came with them , but go direct to CH web site and download the drivers and control panel from there , and never had any issues with them , so check CH web site for any driver updates.
regards alan. 8)

Re: CH Products on P3Dv4

Posted: 24 Sep 2018, 06:21
by guillaume78150
Lewis - A2A wrote:P3dv4 has two input options under settings. Change this and things will probably work for you. A system or sim restart might be needed upon changing the setting.

Thanks,
Lewis
That was it, I switched to "Direct imput" and both pedals and sticks are recognized. The throttle wheel on the fighter stick is not recognized, I guess it's a matter of calibration.
Thanks anyway.

G.

Re: CH Products on P3Dv4

Posted: 24 Sep 2018, 08:30
by scottb613
Hi Folks,

I’ve used a full CH HOTAS since game port days - I think I’m on my third setup - Bob Church (stickworks) who created the software and drivers left the company after many years - prior to Win10 - CH never invested in finding a replacement... Win10 had many reported issues with the Control Manager software/drivers and popular opinion suggests not installing any of it - simply using the native Windows drivers instead... That’s what I’ve been doing since I had some issues and it works fine - granted you lose the very powerful scripting language that came with Control Manager... Your mileage may vary...

Regards,
Scott


Sent from my iPad using Tapatalk

Re: CH Products on P3Dv4

Posted: 24 Sep 2018, 10:35
by dvm
I have a question for anyone in the know. In my p3Dv4 installation my input method is "Raw" which I would assume is default. I have three devices my G-940 stick,crosswind pedals and my Bodner controller (home made throttle & switch panel). They all work fine what would the the direct input option facilitate ? I guess if it ain't broke don't fix would apply but I am curious.