Multiplicity is a program that permits sharing across different desktops.
https://www.stardock.com/products/multiplicity/
Since there is also the "twitching" of the HDG Bug w/ default GPS, I assume something else may be goin on. I noticed this .ini has GNS_430_1
AND GNS_430.1.DEFAULT ???
RXP .ini: (I use the single G430) - Also, Jean-Luc is in the loop on this.
[GNS_430_1]
; is the master device if true.
MasterDevice = true
; selects COM/NAV Radios '1' or '2'.
RadiosPair = 1
; uses computer time if true, simulator time otherwise.
ComputerTime = false
; integral lighting percent (0 to 100)
Rheostat.Display = 100
; integral lighting percent (0 to 100)
Rheostat.Buttons = 75
; connects GPS to Autopilot if true.
LinkOto = true
; connects GPS to HSI if true.
LinkHsi = true
; connects GPS to HSI course motor if true.
LinkCrs = false
; connects GPS to OBS input if true (LinkHsi/OBS or AutoNavSource/OBS) (NB: HSI/OBS = NAV1 OBS).
LinkObs = false
; connects GPS to VOR if true.
LinkVor = false
; connects CDI key to NAV/GPS switch if true.
AutoNavGps = true
; selects VLOC NAV '1' or '2'. '0' selects same source as 'RadiosPair'.
AutoNavSource = 0
; sets device power source: ALWAYS_ON,AVIONICS_BUS,MAIN_BATTERY
PowerSource = AVIONICS_BUS
; sets device power knob switch mode: NONE,DEFAULT_ON,DEFAULT_OFF
PowerKnob = DEFAULT_OFF
; connects GPS to Shadin Air Data computer if true.
UseAirData = true
; connects GPS to Shadin Fuel Data computer if true.
UseFuelData = true
; connects GPS to RYAN 9900BX if true.
UseRyanTcad = false
; sets TCAD sound alerts volume in percent: 0 to 100.
RyanTcadVolume = 50
; connects GPS #1 to GPS #2 if true (both required).
UseCrossFill = false
; enable device failures if true.
UseFailures = false
; uses Simulator GPS commands if true.
UseSimGpsCmds = true
; updates Simulator GPS flight plan if true.
LinkSimGps = false
; saves the active route as a Simulator flight plan if true.
AutoSavePln = false
; use legacy mouse (left CCW, right CW, middle Push) (override instances settings)
UseAltMouse = false
; use legacy GNS WAAS 3rd party aircraft panel variables (L:Vars).
UseLegacyVars = false
; sets fuel type: AVGAS,JETA,JETB
FuelType = AVGAS
; sets TAWS type: TERR,TAWS
TawsMode = TERR
; sets TAWS surface: HARD,HARD_SOFT,WATER,ANY
TawsSurface = HARD_SOFT
; TAWS minimum runway length (feet)
TawsMinLength = 40
; HSI lateral deviation scale factor.
CdiScale = 1
; HSI vertical deviation scale factor.
GsiScale = 1
; sets master sound volume in percent: 0 to 100.
MasterVolume = 100
; mute sound when simulator window looses focus if false.
NoAudioFocus = false
; selects the CPU running the trainer process: 1 to 32
; 0: last core, -1: automatic.
CpuAffinity = -1
; connects to: 'PFC_STACK','PFC_430','PFC_530' or any '#PID' (#D002 for PFC_430)
; no value connects to first found, 'OFF' disables connection.
HardwareDevice =
; hardware selector number or -1 to disable.
HardwareIdx = -1
[GNS_430_1.DEFAULT]
; show screen only gauge if true.
nobezel = false
; screen only border size (pixels).
border.size = 0
; screen only border color (#RGB or #RGBA).
border.rgba = #000000
; display mouse tooltips if true.
tooltips = false
; enable mouse clickspots if true, disable if false.
usemouse = true
; enable alternate click-spots (left CCW, right CW, middle Push) if true.
usealtmouse = false
; auto-resize dimension (width,height)
refsize =
; left mouse button on the screen toggles popup window by ident (ex: GPS_PANEL or 225).
popleft =
; right mouse button on the screen toggles popup window by ident (ex: GPS_PANEL or 225).
popright =
; adjust brightness (0 to 100)
brightness.bezel = 100
; offset brightness (-100 to +100)
brightness.screen = 0
[GNS_530_1]
; is the master device if true.
MasterDevice = true
; selects COM/NAV Radios '1' or '2'.
RadiosPair = 1
; uses computer time if true, simulator time otherwise.
ComputerTime = false
; integral lighting percent (0 to 100)
Rheostat.Display = 100
; integral lighting percent (0 to 100)
Rheostat.Buttons = 75
; connects GPS to Autopilot if true.
LinkOto = true
; connects GPS to HSI if true.
LinkHsi = true
; connects GPS to HSI course motor if true.
LinkCrs = false
; connects GPS to OBS input if true (LinkHsi/OBS or AutoNavSource/OBS) (NB: HSI/OBS = NAV1 OBS).
LinkObs = false
; connects GPS to VOR if true.
LinkVor = false
; connects CDI key to NAV/GPS switch if true.
AutoNavGps = true
; selects VLOC NAV '1' or '2'. '0' selects same source as 'RadiosPair'.
AutoNavSource = 0
; sets device power source: ALWAYS_ON,AVIONICS_BUS,MAIN_BATTERY
PowerSource = AVIONICS_BUS
; sets device power knob switch mode: NONE,DEFAULT_ON,DEFAULT_OFF
PowerKnob = NONE
; connects GPS to Shadin Air Data computer if true.
UseAirData = true
; connects GPS to Shadin Fuel Data computer if true.
UseFuelData = true
; connects GPS to RYAN 9900BX if true.
UseRyanTcad = false
; sets TCAD sound alerts volume in percent: 0 to 100.
RyanTcadVolume = 50
; connects GPS #1 to GPS #2 if true (both required).
UseCrossFill = false
; enable device failures if true.
UseFailures = false
; uses Simulator GPS commands if true.
UseSimGpsCmds = true
; updates Simulator GPS flight plan if true.
LinkSimGps = false
; saves the active route as a Simulator flight plan if true.
AutoSavePln = false
; use legacy mouse (left CCW, right CW, middle Push) (override instances settings)
UseAltMouse = false
; use legacy GNS WAAS 3rd party aircraft panel variables (L:Vars).
UseLegacyVars = false
; sets fuel type: AVGAS,JETA,JETB
FuelType = AVGAS
; sets TAWS type: TERR,TAWS
TawsMode = TERR
; sets TAWS surface: HARD,HARD_SOFT,WATER,ANY
TawsSurface = HARD_SOFT
; TAWS minimum runway length (feet)
TawsMinLength = 40
; HSI lateral deviation scale factor.
CdiScale = 1
; HSI vertical deviation scale factor.
GsiScale = 1
; sets master sound volume in percent: 0 to 100.
MasterVolume = 100
; mute sound when simulator window looses focus if false.
NoAudioFocus = false
; selects the CPU running the trainer process: 1 to 32
; 0: last core, -1: automatic.
CpuAffinity = -1
; connects to: 'PFC_STACK','PFC_430','PFC_530' or any '#PID' (#D002 for PFC_430)
; no value connects to first found, 'OFF' disables connection.
HardwareDevice =
; hardware selector number or -1 to disable.
HardwareIdx = -1
[GNS_530_1.DEFAULT]
; show screen only gauge if true.
nobezel = false
; screen only border size (pixels).
border.size = 0
; screen only border color (#RGB or #RGBA).
border.rgba = #000000
; display mouse tooltips if true.
tooltips = false
; enable mouse clickspots if true, disable if false.
usemouse = true
; enable alternate click-spots (left CCW, right CW, middle Push) if true.
usealtmouse = false
; auto-resize dimension (width,height)
refsize =
; left mouse button on the screen toggles popup window by ident (ex: GPS_PANEL or 225).
popleft =
; right mouse button on the screen toggles popup window by ident (ex: GPS_PANEL or 225).
popright =
; adjust brightness (0 to 100)
brightness.bezel = 100
; offset brightness (-100 to +100)
brightness.screen = 0
[GNS_430_2]
; is the master device if true.
MasterDevice = false
; selects COM/NAV Radios '1' or '2'.
RadiosPair = 2
; uses computer time if true, simulator time otherwise.
ComputerTime = false
; integral lighting percent (0 to 100)
Rheostat.Display = 100
; integral lighting percent (0 to 100)
Rheostat.Buttons = 75
; connects GPS to Autopilot if true.
LinkOto = true
; connects GPS to HSI if true.
LinkHsi = true
; connects GPS to HSI course motor if true.
LinkCrs = false
; connects GPS to OBS input if true (LinkHsi/OBS or AutoNavSource/OBS) (NB: HSI/OBS = NAV1 OBS).
LinkObs = false
; connects GPS to VOR if true.
LinkVor = false
; connects CDI key to NAV/GPS switch if true.
AutoNavGps = true
; selects VLOC NAV '1' or '2'. '0' selects same source as 'RadiosPair'.
AutoNavSource = 0
; sets device power source: ALWAYS_ON,AVIONICS_BUS,MAIN_BATTERY
PowerSource = AVIONICS_BUS
; sets device power knob switch mode: NONE,DEFAULT_ON,DEFAULT_OFF
PowerKnob = NONE
; connects GPS to Shadin Air Data computer if true.
UseAirData = true
; connects GPS to Shadin Fuel Data computer if true.
UseFuelData = true
; connects GPS to RYAN 9900BX if true.
UseRyanTcad = false
; sets TCAD sound alerts volume in percent: 0 to 100.
RyanTcadVolume = 50
; connects GPS #1 to GPS #2 if true (both required).
UseCrossFill = false
; enable device failures if true.
UseFailures = false
; uses Simulator GPS commands if true.
UseSimGpsCmds = false
; updates Simulator GPS flight plan if true.
LinkSimGps = false
; saves the active route as a Simulator flight plan if true.
AutoSavePln = false
; use legacy mouse (left CCW, right CW, middle Push) (override instances settings)
UseAltMouse = false
; use legacy GNS WAAS 3rd party aircraft panel variables (L:Vars).
UseLegacyVars = false
; sets fuel type: AVGAS,JETA,JETB
FuelType = AVGAS
; sets TAWS type: TERR,TAWS
TawsMode = TERR
; sets TAWS surface: HARD,HARD_SOFT,WATER,ANY
TawsSurface = HARD_SOFT
; TAWS minimum runway length (feet)
TawsMinLength = 40
; HSI lateral deviation scale factor.
CdiScale = 1
; HSI vertical deviation scale factor.
GsiScale = 1
; sets master sound volume in percent: 0 to 100.
MasterVolume = 100
; mute sound when simulator window looses focus if false.
NoAudioFocus = false
; selects the CPU running the trainer process: 1 to 32
; 0: last core, -1: automatic.
CpuAffinity = -1
; connects to: 'PFC_STACK','PFC_430','PFC_530' or any '#PID' (#D002 for PFC_430)
; no value connects to first found, 'OFF' disables connection.
HardwareDevice =
; hardware selector number or -1 to disable.
HardwareIdx = -1
[GNS_430_2.DEFAULT]
; show screen only gauge if true.
nobezel = false
; screen only border size (pixels).
border.size = 0
; screen only border color (#RGB or #RGBA).
border.rgba = #000000
; display mouse tooltips if true.
tooltips = false
; enable mouse clickspots if true, disable if false.
usemouse = true
; enable alternate click-spots (left CCW, right CW, middle Push) if true.
usealtmouse = false
; auto-resize dimension (width,height)
refsize =
; left mouse button on the screen toggles popup window by ident (ex: GPS_PANEL or 225).
popleft =
; right mouse button on the screen toggles popup window by ident (ex: GPS_PANEL or 225).
popright =
; adjust brightness (0 to 100)
brightness.bezel = 100
; offset brightness (-100 to +100)
brightness.screen = 0
[GNS_530_2]
; is the master device if true.
MasterDevice = false
; selects COM/NAV Radios '1' or '2'.
RadiosPair = 2
; uses computer time if true, simulator time otherwise.
ComputerTime = false
; integral lighting percent (0 to 100)
Rheostat.Display = 100
; integral lighting percent (0 to 100)
Rheostat.Buttons = 75
; connects GPS to Autopilot if true.
LinkOto = true
; connects GPS to HSI if true.
LinkHsi = true
; connects GPS to HSI course motor if true.
LinkCrs = false
; connects GPS to OBS input if true (LinkHsi/OBS or AutoNavSource/OBS) (NB: HSI/OBS = NAV1 OBS).
LinkObs = false
; connects GPS to VOR if true.
LinkVor = false
; connects CDI key to NAV/GPS switch if true.
AutoNavGps = true
; selects VLOC NAV '1' or '2'. '0' selects same source as 'RadiosPair'.
AutoNavSource = 0
; sets device power source: ALWAYS_ON,AVIONICS_BUS,MAIN_BATTERY
PowerSource = AVIONICS_BUS
; sets device power knob switch mode: NONE,DEFAULT_ON,DEFAULT_OFF
PowerKnob = NONE
; connects GPS to Shadin Air Data computer if true.
UseAirData = true
; connects GPS to Shadin Fuel Data computer if true.
UseFuelData = true
; connects GPS to RYAN 9900BX if true.
UseRyanTcad = false
; sets TCAD sound alerts volume in percent: 0 to 100.
RyanTcadVolume = 50
; connects GPS #1 to GPS #2 if true (both required).
UseCrossFill = false
; enable device failures if true.
UseFailures = false
; uses Simulator GPS commands if true.
UseSimGpsCmds = true
; updates Simulator GPS flight plan if true.
LinkSimGps = false
; saves the active route as a Simulator flight plan if true.
AutoSavePln = false
; use legacy mouse (left CCW, right CW, middle Push) (override instances settings)
UseAltMouse = false
; use legacy GNS WAAS 3rd party aircraft panel variables (L:Vars).
UseLegacyVars = false
; sets fuel type: AVGAS,JETA,JETB
FuelType = AVGAS
; sets TAWS type: TERR,TAWS
TawsMode = TERR
; sets TAWS surface: HARD,HARD_SOFT,WATER,ANY
TawsSurface = HARD_SOFT
; TAWS minimum runway length (feet)
TawsMinLength = 40
; HSI lateral deviation scale factor.
CdiScale = 1
; HSI vertical deviation scale factor.
GsiScale = 1
; sets master sound volume in percent: 0 to 100.
MasterVolume = 100
; mute sound when simulator window looses focus if false.
NoAudioFocus = false
; selects the CPU running the trainer process: 1 to 32
; 0: last core, -1: automatic.
CpuAffinity = -1
; connects to: 'PFC_STACK','PFC_430','PFC_530' or any '#PID' (#D002 for PFC_430)
; no value connects to first found, 'OFF' disables connection.
HardwareDevice =
; hardware selector number or -1 to disable.
HardwareIdx = -1
[GNS_530_2.DEFAULT]
; show screen only gauge if true.
nobezel = false
; screen only border size (pixels).
border.size = 0
; screen only border color (#RGB or #RGBA).
border.rgba = #000000
; display mouse tooltips if true.
tooltips = false
; enable mouse clickspots if true, disable if false.
usemouse = true
; enable alternate click-spots (left CCW, right CW, middle Push) if true.
usealtmouse = false
; auto-resize dimension (width,height)
refsize =
; left mouse button on the screen toggles popup window by ident (ex: GPS_PANEL or 225).
popleft =
; right mouse button on the screen toggles popup window by ident (ex: GPS_PANEL or 225).
popright =
; adjust brightness (0 to 100)
brightness.bezel = 100
; offset brightness (-100 to +100)
brightness.screen = 0